Launching soon. This site is informational for now, and Capitol Garage Door is not booking work yet.

Garage Door Won’t Close: Causes and Repairs in Sacramento

Not a licensed contractor.

A garage door that won’t close, or that starts down and then reverses, is one of the most common garage door problems in Sacramento-area homes. The good news is that the cause is often simple: a blocked or misaligned safety sensor, a setting on the opener, or something in the door’s path. Sometimes it is mechanical, such as a worn roller, a bent track or a broken spring. This guide covers what to check, what to leave alone, and what repairs typically cost here. Capitol Garage Door is an owner-operated business in Wilton that is launching soon.

Launching soon. Capitol Garage Door is not booking work yet. Tell us your town and what your garage door is doing, and you will hear from us when we open.

Symptoms and what they usually mean

  • The door starts down, then reverses back up. Most often the safety sensors, or the opener’s close-force setting.
  • The opener light blinks and the door will not go down. Usually a sensor problem.
  • The door closes only while you hold the wall button. The opener is overriding a sensor fault. The sensors still need attention.
  • The door stops partway and grinds. A bent track, a damaged roller or an obstruction.
  • The door closes crooked or leaves a gap on one side. A cable or spring problem, or a door that has shifted in its track.
  • Nothing happens at all. Power, the remote, or the opener itself.

Safe checks to try first

  1. Clear the path. Look for anything near the door: a trash can, a broom, a rake, a box.
  2. Look at the sensor lights. Two small sensors sit a few inches off the floor on each side. Usually one light is green and one is amber. If one is off or blinking, they are out of line or blocked.
  3. Wipe the sensor lenses. Dust and cobwebs are common in valley garages. A soft cloth is enough.
  4. Check the sensor alignment. If a bracket got bumped, gently nudge the sensor until its light goes steady. Do not bend the bracket hard.
  5. Check for low sun. In late afternoon, direct sunlight hitting a sensor can confuse it. This is common with west-facing garages in the summer.
  6. Try the wall button to rule out a remote battery.

If the door still will not close, stop there.

Mechanical causes

Worn or broken rollers. Rollers that have lost bearings can catch in the track and stop the door. See garage door roller replacement.

Bent or loose track. A bumped track can pinch the rollers. See garage door off track.

Broken spring or cable. A door with a broken spring may close too hard, close crooked, or not respond at all. See garage door spring replacement and garage door cable repair.

Opener limit and force settings. If the limit setting is off, the opener may think the door has reached the floor early. If the force is set too low, the opener may reverse at the slightest resistance. See garage door opener repair.

Damaged bottom panel. A dented bottom section can catch on the track or the floor. See garage door panel replacement.

What not to do

  • Do not disconnect the safety sensors or hold the button down as a long-term fix. The sensors are what stop a closing door from hitting a child, a pet or a car.
  • Do not force a door down that is binding in the track.
  • Do not touch springs, cables or bottom brackets.

If the door is stuck open at night

Lock the interior door from the garage into the house, move valuables out of sight, and keep the opener unplugged if the door is binding so nobody runs it again. If the door is level, the spring is intact and the problem is only the opener, a fully open door can sometimes be lowered by hand after the emergency release is pulled. Do this with two people and only if the door moves smoothly.

What a repair visit involves

  1. Check the sensors, wiring and opener settings first, since they are the most common cause.
  2. Inspect the rollers, tracks, hinges, springs and cables.
  3. Explain what is wrong and give a written price before any work.
  4. Repair and adjust once you approve.
  5. Test closing force, auto-reverse and sensors, so the door closes safely every time.

What affects the cost of repair

  • The cause. A sensor that needs aligning is much simpler than a bent track or a broken spring.
  • Parts needed. Sensors, opener parts, rollers, cables and springs all differ.
  • Damage from forcing the door. Running a door that is binding can bend tracks or sections.

Pricing depends on the exact issue and parts needed. You will get a written price before any work starts, and nothing is added without your OK.

What to expect from Capitol Garage Door

  • The owner answers and does the work.
  • Honest answers. If it is a dirty sensor, you will hear that.
  • Written price before work.
  • Safety tested. Every job ends with an auto-reverse test.

Service will cover Roseville, Folsom, Elk Grove, Rancho Cordova and the rest of the service area. If the door will not go up at all, see garage door won’t open.

Garage door won’t close: questions

Why does my garage door go down and then back up?

The opener thinks something is in the way. Check for a blocked or misaligned sensor first, then for anything binding in the track. A close-force setting that is too sensitive can also cause it.

Why does it close only when I hold the button?

Holding the wall button overrides the sensors on most openers. That is a sign the sensors are blocked or out of line and need attention.

Can sunlight really stop a garage door from closing?

Yes. Strong, low sunlight shining straight into a sensor lens can stop it from seeing the beam from the other side. A small shade or a slight adjustment usually solves it.

Is it safe to bypass the sensors?

No. The sensors are a required safety feature that stops the door from closing on people, pets and cars.

Launching soon. Capitol Garage Door is not booking work yet. Tell us your town and what your garage door is doing, and you will hear from us when we open.